当前位置:首页 ? » 电泳设备 电泳设备工艺 ? 正文

电泳槽循环泵简介中英对照版

567 人参与  2012年01月20日 00:00  分类 : 电泳设备 电泳设备工艺  评论

?Pumps????????? 泵

End suction centrifugal pumps, both horizontal and vertical, are commonly used in electrocoat systems. The choice of pumps should be determined by economics, design constraints, or designer preference. 在电泳系统中,一般使用卧式及立式端吸式离心泵,泵的选用取决于经济条件,设计的限制或设计师的偏好。 Vertical turbine pumps (equivalent to Process Systems Thrust Head) have proven cost effective due to the ease of maintenance and long service life. 垂直涡轮泵(相当于系统过程推动头)由于易于维修和较长的使用期限已被证明是节省成本的。 Vertical, chair-mount pumps in weirs are equipped with long shafts to prevent foaming which can occur with changing weir levels. The suction bell extension? should be no closer than? 1.5 pipe diameters of the weir bottom to minimize vortexing and permit greater pump-down of the weir during tank cleaning.? All pumps should be protected to prevent large debris from damaging impellers and pump housings. Vertical pumps should be equipped with a removable stainless steel screen (.25 inch dia.) installed ahead of the pump. A non-conductive coating should be applied to the screen to prevent paint from coating the screen. (Electrocoating the screens in the electrocoat tank and then baking them has worked well.) The screens should be checked for plugging daily and cleaned once per month. 安装在溢流槽中的立式泵要求长轴,可防止在改变溢流液位时产生泡沫,长轴也要有较粗的轴径,以延长使用寿命,泵吸口要伸到距溢流槽底不少于1.5倍管径处,以尽量减小涡流及在清理溢流槽时能够较大限度的抽空溢流槽。所有泵都应有防止大的染质损坏叶轮及泵谷的保护措施。立式泵要配有安在泵头(吸口)的双层可拆卸不锈钢网 (0.25英尺的直径),要将钢网涂以绝缘涂层以防止沉积上电泳漆(在电泳槽中泳好的钢丝网,烘干后即可),对保护网应每天要进行堵漏检查并每月清洗一次。 Horizontal pumps should be equipped with reliable valves to isolate the pump from the system. The pumps should also be installed so that they have a low point drain and a DI water connection to permit pump flushing. The installation of spare pumps piped into the system is not recommended. They have been found to be a source of dirt and are difficult to keep clean.? However, a spare pump housing should be available on site for replacement during maintenance.? If, spare pumps are piped into the system they should be isolated from the paint and flushed with DI water when not in use.       卧式泵必须配有可靠的阀将泵与系统分隔,泵还要装低位排净口及供冲洗用的去离子水接管口,我们发现备用泵是污染源,并且很难保持清洁,因此不推荐将备用泵安装在系统中。然而,应该是在维修过程中更换使用的备用泵,如果用管路将备用泵接入系统中,必须将其与漆液隔离,不使用时必须用去离子水冲洗,建议采用柔性泵连接件以减小管路张力及增加泵机械密封的寿命。 Pump housings should be constructed of gray cast iron: nodular cast iron should not be used. Impellers and shafts should be made of 316 stainless steel to minimize wear.? (See Figure 8 for typical circulation system layouts). 泵毂要用灰铸铁,不要使用球墨铸铁,叶轮及轴要用316不锈钢制成,以降低磨损(见图8典型的循环系统布置)。
阅读全文

本文标签:电泳槽  循环泵  

<< 上一篇 下一篇 >>

  • 相关文章
  • Powered By Z-Blog Copyright dianyongqi.com Rights Reserved.
    湘ICP备17018394号-2
    免责声明

    本站内容由网友提供,版权归原作者本人所有,本网站不对网站真实性负责,如有违反您的利益,请与我们联系!QQ:3323300542

    亚洲系列 动漫卡通先锋